Kommunal.az

Breathing gas

Trimix scuba cylinder label
Uses	Gas used for human respiration
Related items	Air, Heliox, Nitrox, Oxygen, Trimix, Gas blending for scuba diving, Diving cylinder, Scuba set, Rebreather

A breathing gas is a mixture of gaseous chemical elements and compounds used for respiration. Air is the most common and only natural breathing gas, but other mixtures of gases, or pure oxygen, are also used in breathing equipment and enclosed habitats. Oxygen is the essential component for any breathing gas. Breathing gases for hyperbaric use have been developed to improve on the performance of ordinary air by reducing the risk of decompression sickness, reducing the duration of decompression, reducing nitrogen narcosis or reducing work of breathing and allowing safer deep diving.

A breathing gas is a mixture of gaseous chemical elements and compounds used for respiration. Air is the most common and only natural breathing gas. Other mixtures of gases, or pure oxygen, are also used in breathing equipment and enclosed habitats such as scuba equipment, surface supplied diving equipment, recompression chambers, high-altitude mountaineering, high-flying aircraft, submarines, space suits, spacecraft, medical life-support and first aid equipment, and anaesthetic machines.^[1][2][3]

Oxygen is the essential component for any breathing gas, at a partial pressure of between roughly 0.16 and 1.60 bar at the ambient pressure, occasionally lower for high altitude mountaineering, or higher for hyperbaric oxygen treatment. The oxygen is usually the only metabolically active component unless the gas is an anaesthetic mixture. Some of the oxygen in the breathing gas is consumed by the metabolic processes, and the inert components are unchanged, and serve mainly to dilute the oxygen to an appropriate concentration, and are therefore also known as diluent gases.

Most breathing gases therefore are a mixture of oxygen and one or more metabolically inert gases.^[1][3] Breathing gases for hyperbaric use have been developed to improve on the performance of ordinary air by reducing the risk of decompression sickness, reducing the duration of decompression, reducing nitrogen narcosis or allowing safer deep diving.^[1][3] The techniques used to fill diving cylinders with gases other than air or pure oxygen are called gas blending.^[4][5]

Breathing gases for use at ambient pressures below normal atmospheric pressure are usually pure oxygen or air enriched with oxygen to provide sufficient oxygen to maintain life and consciousness, or to allow higher levels of exertion than would be possible using air. It is common to provide the additional oxygen as a pure gas added to the breathing air at inhalation, or though a life-support system.

When used by an underwater diver, a breathing gas may also be referred to as a diving gas.^[6] A safe breathing gas for hyperbaric use has four essential features:

• It must contain sufficient oxygen to support life, consciousness and work rate of the breather.^[1][2][3]
• It must not contain harmful contaminants. Carbon monoxide and carbon dioxide are common poisons which may contaminate breathing gases. There are many other possibilities.^[1][2][3]
• It must not become toxic when being breathed at high pressure such as when underwater. Oxygen and nitrogen are examples of gases that become toxic under pressure.^[1][2][3]
• It must not be too dense to breathe. Work of breathing increases with density and viscosity. Maximum ventilation drops by about 50% when density is equivalent to air at 30 msw, and carbon dioxide levels rise unacceptably for moderate exercise with a gas density exceeding 6 g/litre. Breathing gas density of 10 g/litre or more may cause runaway hypercapnia even at very low work levels, with potentially fatal effects.^[7]

These common diving breathing gases are used:

• Air is a mixture of 21% oxygen, 78% nitrogen, and approximately 1% other trace gases, primarily argon; to simplify calculations this last 1% is usually treated as if it were nitrogen. Being freely available and simple to use, it is the most common diving gas.^[1][2][3] As its nitrogen component causes nitrogen narcosis, it is considered to have a safe depth limit of about 40 metres (130 feet) for most divers, although the maximum operating depth (MOD) of air taking an allowable oxygen partial pressure of 1,6 bar is 66.2 metres (217 feet).^[1][3][8] Breathing air is air meeting specified standards for contaminants.
• Pure oxygen is mainly used to speed the shallow decompression stops at the end of a military, commercial, or technical dive. Risk of acute oxygen toxicity increases rapidly at pressures greater than 6 metres sea water.^[1][2][3][8] It was much used in frogmen's rebreathers, and is still used by attack swimmers.^{[2][8][9][10]}
• Mixed gases are mixtures of two or more gases specifically blended for use as breathing gas for divers. They may be mixed to the composition required before the dive, for open circuit use, or produced in the breathing circuit of a rebreather during the dive. Diving using mixed gases is referred to as mixed gas diving.^[11]
  • Nitrox is a mixture of oxygen and nitrogen, either by mixing oxygen with air, or by removing nitrogen from air, and generally refers to mixtures which are more than 21% oxygen. It can be used as a tool to accelerate in-water decompression stops or to decrease the risk of decompression sickness and thus prolong a dive (a common misconception is that the diver can go deeper; this is not true, owing to a shallower maximum operating depth than with conventional air).^{[1][2][3][12]}
  • Trimix is a mixture of oxygen, nitrogen, and helium and is often used at depth in technical diving and commercial diving instead of air to decrease the work of breathing, reduce nitrogen narcosis, and avoid the dangers of oxygen toxicity.^[1][2][3]
    • Heliair is a form of trimix that is easily blended from helium and air without using pure oxygen. It always has a 21:79 ratio of oxygen to nitrogen; the balance of the mix is helium.^[3][13]
  • Heliox is a mixture of oxygen and helium and is often used in the deep phase of a commercial deep dive to eliminate nitrogen narcosis and reduce density, to limit the work of breathing.^{[1][2][3][14]} Heliox is the standard mixture type for deep offshore saturation diving.^[15]
  • Hydreliox is a mixture of oxygen, helium, and hydrogen and is used for dives below 130 metres in commercial diving.^{[1][3][14][16][17]} Experimental work using hydreliox is also done in deep technical diving, where the hydrogen is used to reduce HPNS.
  • Hydrox, a gas mixture of hydrogen and oxygen, is used as a breathing gas in very deep diving.^{[1][3][14][16][18]}
  • Neox (also called neonox) is a mixture of oxygen and neon sometimes employed in deep commercial diving. It is rarely used due to its cost. Also, DCS symptoms produced by neon ("neox bends") have a poor reputation; they are widely reported to be more severe than those produced by an exactly equivalent dive-table and mix with helium.^{[1][3][14][19]}

Commonly accepted breathing gas container colour coding in the offshore diving industry.^[20]

Gas	Symbol	Typical shoulder colours	Cylinder shoulder	Quad upper frame/ frame valve end
Medical oxygen	O2		White	White
Oxygen and helium mixtures (Heliox)	O2/He		Brown and white quarters or bands	Brown and white short (8 inches (20 cm)) alternating bands
Oxygen, helium and nitrogen mixtures (Trimix)	O2/He/N2		Black, white and brown quarters or bands	Black, white and brown short (8 inches (20 cm)) alternating bands
Oxygen and nitrogen mixtures (Nitrox) including air	N2/O2		Black and white quarters or bands	Black and white short (8 inches (20 cm)) alternating bands

Breathing air is atmospheric air with a standard of purity suitable for human breathing in the specified application. For hyperbaric use, the partial pressure of contaminants is increased in proportion to the absolute pressure, and must be limited to a safe composition for the depth or pressure range in which it is to be used.

Breathing gases for diving are classified by oxygen fraction. The boundaries set by authorities may differ slightly, as the effects vary gradually with concentration and between people, and are not accurately predictable.^[21]

Normoxic

where the oxygen content does not differ greatly from that of air and allows continuous safe use at atmospheric pressure.^[22]

Hyperoxic, or oxygen enriched

where the oxygen content exceeds atmospheric levels, generally to a level where there is some measurable physiological effect over long term use, and sometimes requiring special procedures for handling due to increased fire hazard. The associated risks are oxygen toxicity at depth and fire, particularly in the breathing apparatus.^[21]

Hypoxic

where the oxygen content is less than that of air, generally to the extent that there is a significant risk of measurable physiological effect over the short term. The immediate risk is usually hypoxic incapacitation at or near the surface.^[23]

Breathing gases for diving are mixed from a small number of component gases which provide special characteristics to the mixture which are not available from atmospheric air.

Oxygen (O₂) must be present in every breathing gas.^[1][2][3] This is because it is essential to the human body's metabolic process, which sustains life. The human body cannot store oxygen for later use as it does with food. If the body is deprived of oxygen for more than a few minutes, unconsciousness and death result. The tissues and organs within the body (notably the heart and brain) are damaged if deprived of oxygen for much longer than four minutes.

Filling a diving cylinder with pure oxygen costs considerably more than filling it with compressed air. As oxygen supports combustion and causes rust in diving cylinders, it should be handled with caution when gas blending.^[4][5]

Oxygen has historically been obtained by fractional distillation of liquid air, but is increasingly obtained by non-cryogenic technologies such as pressure swing adsorption (PSA) and vacuum swing adsorption (VSA) technologies.^[24]

The fraction of the oxygen component of a breathing gas mixture is sometimes used when naming the mix:

• hypoxic mixes, strictly, contain less than 21% oxygen, although often a boundary of 16% is used, and are designed only to be breathed at depth as a "bottom gas" where the higher pressure increases the partial pressure of oxygen to a safe level.^[1][2][3] Trimix, Heliox and Heliair are gas blends commonly used for hypoxic mixes and are used in professional and technical diving as deep breathing gases.^[1][3] A minimum operating depth may be assigned to a hypoxic gas mixture, based on the depth at which the partial pressure is equal to the minimum oxygen partial pressure acceptable to the person or organisation using the gas.
• normoxic mixes have the same proportion of oxygen as air, 21%.^[1][3] The maximum operating depth of a normoxic mix could be as shallow as 47 metres (154 feet). Trimix with between 17% and 21% oxygen is often described as normoxic because it contains a high enough proportion of oxygen to be safe to breathe at the surface.
• hyperoxic mixes have more than 21% oxygen. Enriched Air Nitrox (EANx) is a typical hyperoxic breathing gas.^[1][3][12] Hyperoxic mixtures, when compared to air, cause oxygen toxicity at shallower depths but can be used to shorten decompression stops by drawing dissolved inert gases out of the body more quickly.^[8][12]

The fraction of the oxygen determines the greatest depth at which the mixture can safely be used to avoid oxygen toxicity. This depth is called the maximum operating depth.^{[1][3][8][12]}

The concentration of oxygen in a gas mix depends on the fraction and the pressure of the mixture. It is expressed by the partial pressure of oxygen (P_O2).^{[1][3][8][12]} The partial pressure of any component gas in a mixture is calculated as:

partial pressure = total absolute pressure × volume fraction of gas component

For the oxygen component,

P_O2 = P × F_O2

where:

P_O2 = partial pressure of oxygen

P = total pressure

F_O2 = volume fraction of oxygen content

The minimum safe partial pressure of oxygen in a breathing gas is commonly held to be 16 kPa (0.16 bar). Below this partial pressure the diver may be at risk of unconsciousness and death due to hypoxia, depending on factors including individual physiology and level of exertion. When a hypoxic mix is breathed in shallow water it may not have a high enough P_O2 to keep the diver conscious. For this reason normoxic or hyperoxic "travel gases" are used at medium depth between the "bottom" and "decompression" phases of the dive.

The maximum safe P_O2 in a breathing gas depends on exposure time, the level of exercise and the security of the breathing equipment being used. It is typically between 100 kPa (1 bar) and 160 kPa (1.6 bar); for dives of less than three hours it is commonly considered to be 140 kPa (1.4 bar), although the U.S. Navy has been known to authorize dives with a P_O2 of as much as 180 kPa (1.8 bar).^{[1][2][3][8][12]} At high P_O2 or longer exposures, the diver risks oxygen toxicity which may result in a seizure.^[1][2] Each breathing gas has a maximum operating depth that is determined by its oxygen content.^{[1][2][3][8][12]} For therapeutic recompression and hyperbaric oxygen therapy partial pressures of 2.8 bar are commonly used in the chamber, but there is no risk of drowning if the occupant loses consciousness.^[2] For longer periods such as in saturation diving, 0.4 bar can be tolerated over several weeks.

Oxygen analysers are used to measure the oxygen partial pressure in the gas mix.^[4]

Divox is breathing grade oxygen labelled for diving use. In the Netherlands, pure oxygen for breathing purposes is regarded as medicinal as opposed to industrial oxygen, such as that used in welding, and is only available on medical prescription. The diving industry registered Divox as a trademark for breathing grade oxygen to circumvent the strict rules concerning medicinal oxygen thus making it easier for (recreational) scuba divers to obtain oxygen for blending their breathing gas. In most countries, there is no difference in purity in medical oxygen and industrial oxygen, as they are produced by exactly the same methods and manufacturers, but labeled and filled differently. The chief difference between them is that the record-keeping trail is much more extensive for medical oxygen, to more easily identify the exact manufacturing trail of a "lot" or batch of oxygen, in case problems with its purity are discovered. Aviation grade oxygen is similar to medical oxygen, but may have a lower moisture content.^[4]

Gases which have no metabolic function in the breathing gas are used to dilute the gas, and are therefore classed as diluent gases. Some of them have a reversible narcotic effect at high partial pressure, and must therefore be limited to avoid excessive narcotic effects at the maximum pressure at which they are intended to be breathed. Diluent gases also affect the density of the gas mixture and thereby the work of breathing.

Nitrogen (N₂) is a diatomic gas and the main component of air, the cheapest and most common breathing gas used for diving. It causes nitrogen narcosis in the diver, so its use is limited to shallower dives. Nitrogen can cause decompression sickness.^{[1][2][3][25]}

Equivalent air depth is used to estimate the decompression requirements of a nitrox (oxygen/nitrogen) mixture. Equivalent narcotic depth is used to estimate the narcotic potency of trimix (oxygen/helium/nitrogen mixture). Many divers find that the level of narcosis caused by a 30 m (100 ft) dive, whilst breathing air, is a comfortable maximum.^{[1][2][3][26][27]}

Nitrogen in a gas mix is almost always obtained by adding air to the mix.

Helium (He) is an inert gas that is less narcotic than nitrogen at equivalent pressure (in fact there is no evidence for any narcosis from helium at all), and it has a much lower density, so it is more suitable for deeper dives than nitrogen.^[1][3] Helium is equally able to cause decompression sickness. At high pressures, helium also causes high-pressure nervous syndrome, which is a central nervous system irritation syndrome which is in some ways opposite to narcosis.^{[1][2][3][28]}

Helium mixture fills are considerably more expensive than air fills due to the cost of helium and the cost of mixing and compressing the mix.^{[citation needed]}

Helium is not suitable for dry suit inflation owing to its poor thermal insulation properties – compared to air, which is regarded as a reasonable insulator, helium has six times the thermal conductivity.^[29] Helium's low molecular weight (monatomic MW=4, compared with diatomic nitrogen MW=28) increases the pitch of the breather's voice, which may impede communication.^[1][3][30] This is because the speed of sound is faster in a lower molecular weight gas, which increases the resonance frequency of the vocal cords.^[1][30] Helium leaks from damaged or faulty valves more readily than other gases because atoms of helium are smaller allowing them to pass through smaller gaps in seals.

Helium is found in significant amounts only in natural gas, from which it is extracted at low temperatures by fractional distillation.

Neon (Ne) is an inert gas sometimes used in deep commercial diving but is very expensive.^{[1][3][14][19]} Like helium, it is less narcotic than nitrogen, but unlike helium, it does not distort the diver's voice. Compared to helium, neon has superior thermal insulating properties.^[21] Neon has an atomic and molecular weight of approximately 20, compared to 14 for nitrogen and 4 for helium, but nitrogen gas (N₂)has a molecular weight of 28.

Hydrogen (H₂) has been used in deep diving gas mixes but is very explosive when mixed with more than about 4 to 5% oxygen (such as the oxygen found in breathing gas).^{[1][3][14][16]} This limits use of hydrogen to deep dives and imposes complicated protocols to ensure that excess oxygen is cleared from the breathing equipment before breathing hydrogen starts. Like helium, it raises the pitch of the diver's voice. The hydrogen-oxygen mix when used as a diving gas is sometimes referred to as Hydrox. Mixtures containing both hydrogen and helium as diluents are termed hydreliox.

Many gases are not suitable for use in diving breathing gases.^[5][31] Here is an incomplete list of gases commonly present in a diving environment:

Argon (Ar) is an inert gas that is more narcotic than nitrogen, so is not generally suitable as a diving breathing gas.^[32] Argox is used for decompression research.^{[1][3][33][34]} It is sometimes used for dry suit inflation by divers whose primary breathing gas is helium-based, because of argon's good thermal insulation properties. Argon is more expensive than air or oxygen, but considerably less expensive than helium. Argon is a component of natural air, and constitutes 0.934% by volume of the Earth's atmosphere.^[35]

Carbon dioxide (CO₂) is produced by the metabolism in the human body and can cause carbon dioxide poisoning.^[31][36][37] When breathing gas is recycled in a rebreather or life-support system, the carbon dioxide is removed by scrubbers before the gas is re-used.

Carbon monoxide (CO) is a highly toxic gas that competes with dioxygen for binding to hemoglobin, thereby preventing the blood from carrying oxygen (see carbon monoxide poisoning). It is typically produced by incomplete combustion.^{[1][2][5][31]} Four common sources are:

• Internal combustion engine exhaust gas containing CO in the air being drawn into a diving air compressor. CO in the intake air cannot be stopped by any filter. The exhausts of all internal combustion engines running on petroleum fuels contain some CO, and this is a particular problem on boats, where the intake of the compressor cannot be arbitrarily moved as far as desired from the engine and compressor exhausts.
• Heating of lubricants inside the compressor may vaporize them sufficiently to be available to a compressor intake or intake system line.
• In some cases hydrocarbon lubricating oil may be drawn into the compressor's cylinder directly through damaged or worn seals, and the oil may (and usually will) then undergo combustion, being ignited by the immense compression ratio and subsequent temperature rise. Since heavy oils don't burn well – especially when not atomized properly – incomplete combustion will result in carbon monoxide production.
• A similar process is thought^{[by whom?][original research?]} to potentially happen to any particulate material, which contains "organic" (carbon-containing) matter, especially in cylinders which are used for hyperoxic gas mixtures. If the compressor air filter(s) fail, ordinary dust will be introduced to the cylinder, which contains organic matter (since it usually contains humus). A more severe danger is that air particulates on boats and industrial areas, where cylinders are filled, often contain carbon-particulate combustion products (these are what makes a dirt rag black), and these represent a more severe CO danger when introduced into a cylinder.^{[citation needed]}

Carbon monoxide is generally avoided as far as is reasonably practicable by positioning of the air intake in uncontaminated air, filtration of particulates from the intake air, use of suitable compressor design and appropriate lubricants, and ensuring that running temperatures are not excessive. Where the residual risk is excessive, a hopcalite catalyst can be used in the high pressure filter to convert carbon monoxide into carbon dioxide, which is far less toxic.

Hydrocarbons (C_xH_y) are present in compressor lubricants and fuels. They can enter diving cylinders as a result of contamination, leaks,^{[clarification needed]} or due to incomplete combustion near the air intake.^{[2][4][5][31][38]}

• They can act as a fuel in combustion increasing the risk of explosion, especially in high-oxygen gas mixtures.
• Inhaling oil mist can damage the lungs and ultimately cause the lungs to degenerate with severe lipid pneumonia^[39] or emphysema.

The process of compressing gas into a diving cylinder removes moisture from the gas.^[5][31] This is good for corrosion prevention in the cylinder but means that the diver inhales very dry gas. The dry gas extracts moisture from the diver's lungs while underwater contributing to dehydration, which is also thought to be a predisposing risk factor of decompression sickness. Evaporation in the lungs causes a significant heat loss. Dry gas is also uncomfortable, causing a dry mouth and throat and making the diver thirsty. This problem is reduced in rebreathers because the soda lime reaction, which removes carbon dioxide, also puts moisture back into the breathing gas,^[10] and the relative humidity and temperature of exhaled gas is relatively high and there is a cumulative effect due to rebreathing.^[40] In hot climates, open circuit diving can accelerate heat exhaustion because of dehydration. Another concern with regard to moisture content is the tendency of moisture to condense as the gas expands while passing through the regulator; this coupled with the extreme reduction in temperature, also due to the decompression, can cause the moisture to solidify as ice. This icing up in a regulator can cause moving parts to seize and the regulator to fail or free flow. This is one of the reasons that scuba regulators are generally constructed from brass, and chrome plated (for protection). Brass, with its good thermal conductive properties, quickly conducts heat from the surrounding water to the cold, newly decompressed air, helping to prevent icing up.

Gas mixtures must generally be analysed either in process or after blending for quality control. This is particularly important for breathing gas mixtures where errors can affect the health and safety of the end user. It is difficult to detect most gases that are likely to be present in diving cylinders because they are colourless, odourless and tasteless. Electronic sensors exist for some gases, such as oxygen analysers, helium analyser, carbon monoxide detectors and carbon dioxide detectors.^[2][4][5] Oxygen analysers are commonly found underwater in rebreathers.^[10] Oxygen and helium analysers are often used on the surface during gas blending to determine the percentage of oxygen or helium in a breathing gas mix.^[4] Chemical and other types of gas detection methods are not often used in recreational diving, but are used for periodic quality testing of compressed breathing air from diving air compressors.^[4]

Standards for breathing gas quality are published by national and international organisations, and may be enforced in terms of legislation. In the UK, the Health and Safety Executive indicate that the requirements for breathing gases for divers are based on the BS EN 12021:2014. The specifications are listed for oxygen compatible air, nitrox mixtures produced by adding oxygen, removing nitrogen, or mixing nitrogen and oxygen, mixtures of helium and oxygen (heliox), mixtures of helium, nitrogen and oxygen (trimix), and pure oxygen, for both open circuit and reclaim systems, and for high pressure and low pressure supply (above and below 40 bar supply).^[41]

Oxygen content is variable depending on the operating depth, but the tolerance depends on the gas fraction range, being ±0.25% for an oxygen fraction below 10% by volume, ±0.5% for a fraction between 10% and 20%, and ±1% for a fraction over 20%.^[41]

Water content is limited by risks of icing of control valves, and corrosion of containment surfaces – higher humidity is not a physiological problem – and is generally a factor of dew point.^[41]

Other specified contaminants are carbon dioxide, carbon monoxide, oil, and volatile hydrocarbons, which are limited by toxic effects. Other possible contaminants should be analysed based on risk assessment, and the required frequency of testing for contaminants is also based on risk assessment.^[41]

In Australia breathing air quality is specified by Australian Standard 2299.1, Section 3.13 Breathing Gas Quality.^[42]

Gas blending (or gas mixing) of breathing gases for diving is the filling of gas cylinders with non-air breathing gas mixtures. Filling cylinders with a mixture of gases has dangers for both the filler and the diver. During filling there is a risk of fire due to use of oxygen and a risk of explosion due to the use of high-pressure gases. The composition of the mix must be safe for the depth and duration of the planned dive. If the concentration of oxygen is too lean the diver may lose consciousness due to hypoxia and if it is too rich the diver may develop oxygen toxicity. The concentration of inert gases, such as nitrogen and helium, are planned and checked to avoid nitrogen narcosis and decompression sickness.

Methods used include batch mixing by partial pressure or by mass fraction, and continuous blending processes. Completed blends are analysed for composition for the safety of the user. Gas blenders may be required by legislation to prove competence if filling for other persons.

Excessive density of a breathing gas can raise the work of breathing to intolerable levels, and can cause carbon dioxide retention at lower densities.^[7] Helium is used as a component to reduce density as well as to reduce narcosis at depth. Like partial pressure, density of a mixture of gases is in proportion to the volumetric fraction of the component gases, and absolute pressure. The ideal gas laws are adequately precise for gases at respirable pressures.

The density of a gas mixture at a given temperature and pressure can be calculated as:

ρ_m = (ρ₁ V₁ + ρ₂ V₂ + .. + ρ_n V_n) / (V₁ + V₂ + ... + V_n)

where

ρ_m = density of the gas mixture

ρ₁ ... ρ_n = density of each of the components

V₁ ... V_n = partial volume of each of the component gases^[43]

Since gas fraction F_i (volumetric fraction) of each gas can be expressed as V_i / (V₁ + V₂ + ... + V_n )

by substitution,

ρ_m = (ρ₁ F₁ + ρ₂ F₂ + .. + ρ_n F_n)

Breathing gases for use at reduced ambient pressure are used for high altitude flight in unpressurised aircraft, in space flight, particularly in space suits, and for high altitude mountaineering. In all these cases, the primary consideration is providing an adequate partial pressure of oxygen. In some cases the breathing gas has oxygen added to make up a sufficient concentration, and in other cases the breathing gas may be pure or nearly pure oxygen. Closed circuit systems may be used to conserve the breathing gas, which may be in limited supply – in the case of mountaineering the user must carry the supplemental oxygen, and in space flight the cost of lifting mass into orbit is very high.

Medical use of breathing gases other than air include oxygen therapy and anesthesia applications.

Oxygen is required by people for normal cell metabolism.^[44] Air is typically 21% oxygen by volume.^[45] This is normally sufficient, but in some circumstances the oxygen supply to tissues is compromised.

Oxygen therapy, also known as supplemental oxygen, is the use of oxygen as a medical treatment.^[46] This can include for low blood oxygen, carbon monoxide toxicity, cluster headaches, and to maintain enough oxygen while inhaled anesthetics are given.^[47] Long term oxygen is often useful in people with chronically low oxygen such as from severe COPD or cystic fibrosis.^[48][46] Oxygen can be given in a number of ways including nasal cannula, face mask, and inside a hyperbaric chamber.^[49][50]

High concentrations of oxygen can cause oxygen toxicity such as lung damage or result in respiratory failure in those who are predisposed.^[47][45] It can also dry out the nose and increase the risk of fires in those who smoke. The target oxygen saturation recommended depends on the condition being treated. In most conditions a saturation of 94-98% is recommended, while in those at risk of carbon dioxide retention saturations of 88-92% are preferred, and in those with carbon monoxide toxicity or cardiac arrest the saturation should be as high as possible.^[46]

The use of oxygen in medicine become common around 1917.^[51][52] It is on the World Health Organization's List of Essential Medicines.^[53][54] The cost of home oxygen is about US$150 a month in Brazil and US$400 a month in the United States.^[48] Home oxygen can be provided either by oxygen tanks or an oxygen concentrator.^[46] Oxygen is believed to be the most common treatment given in hospitals in the developed world.^[55][46]

The most common approach to general anaesthesia is through the use of inhaled general anesthetics. Each has its own potency which is correlated to its solubility in oil. This relationship exists because the drugs bind directly to cavities in proteins of the central nervous system,^{[clarification needed]} although several theories of general anaesthetic action have been described. Inhalational anesthetics are thought to exact their effects on different parts of the central nervous system. For instance, the immobilizing effect of inhaled anesthetics results from an effect on the spinal cord whereas sedation, hypnosis and amnesia involve sites in the brain.^[56]: 515

An inhalational anaesthetic is a chemical compound possessing general anaesthetic properties that can be delivered via inhalation. Agents of significant contemporary clinical interest include volatile anaesthetic agents such as isoflurane, sevoflurane and desflurane, and anaesthetic gases such as nitrous oxide and xenon.

Anaesthetic gases are administered by anaesthetists (a term which includes anaesthesiologists, nurse anaesthetists, and anaesthesiologist assistants) through an anaesthesia mask, laryngeal mask airway or tracheal tube connected to an anaesthetic vaporiser and an anaesthetic delivery system. The anaesthetic machine (UK English) or anesthesia machine (US English) or Boyle's machine is used to support the administration of anaesthesia. The most common type of anaesthetic machine in use in the developed world is the continuous-flow anaesthetic machine, which is designed to provide an accurate and continuous supply of medical gases (such as oxygen and nitrous oxide), mixed with an accurate concentration of anaesthetic vapour (such as isoflurane), and deliver this to the patient at a safe pressure and flow. Modern machines incorporate a ventilator, suction unit, and patient monitoring devices. Exhaled gas is passed through a scrubber to remove carbon dioxide, and the anaesthetic vapour and oxygen are replenished as required before the mixture is returned to the patient.^{[citation needed]}

• Mechanical ventilation – Method to mechanically assist or replace spontaneous breathing
• Diving air compressor – Machine used to compress breathing air for use by underwater divers
• Diving cylinder – Container to supply high pressure gas for diving operations
• Booster pump – Machine to increase pressure of a fluid
• Industrial gas – Gaseous materials produced for use in industry

• Media related to Breathing gases at Wikimedia Commons
• Westfalen (2004). "Fact sheet on Divox" (PDF) (in Dutch). Westfalen. Archived from the original (PDF) on 2011-07-24. Retrieved 2008-08-29.
• Taylor, L. "A Brief History Of Mixed Gas Diving". Retrieved 2008-08-29.
• OSHA. "Commercial Diving Regulations (Standards - 29 CFR) - Mixed-gas diving. - 1910.426". U.S. Department of Labor, Occupational Safety & Health Administration. Retrieved 2008-08-29.